LU Kun (陆坤), SONG Yuntao (宋云涛), NIU Erwu (牛二武), ZHOU Tinzhi (周挺志), WANG Zhongwei (王忠伟), CHEN Yonghua (陈永华), ZHU Yinfeng (朱银峰). Evolution of the Design of Cold Mass Support for the ITER Magnet Feeder System[J]. Plasma Science and Technology, 2013, 15(2): 196-200. DOI: 10.1088/1009-0630/15/2/25
Citation:
LU Kun (陆坤), SONG Yuntao (宋云涛), NIU Erwu (牛二武), ZHOU Tinzhi (周挺志), WANG Zhongwei (王忠伟), CHEN Yonghua (陈永华), ZHU Yinfeng (朱银峰). Evolution of the Design of Cold Mass Support for the ITER Magnet Feeder System[J]. Plasma Science and Technology, 2013, 15(2): 196-200. DOI: 10.1088/1009-0630/15/2/25
LU Kun (陆坤), SONG Yuntao (宋云涛), NIU Erwu (牛二武), ZHOU Tinzhi (周挺志), WANG Zhongwei (王忠伟), CHEN Yonghua (陈永华), ZHU Yinfeng (朱银峰). Evolution of the Design of Cold Mass Support for the ITER Magnet Feeder System[J]. Plasma Science and Technology, 2013, 15(2): 196-200. DOI: 10.1088/1009-0630/15/2/25
Citation:
LU Kun (陆坤), SONG Yuntao (宋云涛), NIU Erwu (牛二武), ZHOU Tinzhi (周挺志), WANG Zhongwei (王忠伟), CHEN Yonghua (陈永华), ZHU Yinfeng (朱银峰). Evolution of the Design of Cold Mass Support for the ITER Magnet Feeder System[J]. Plasma Science and Technology, 2013, 15(2): 196-200. DOI: 10.1088/1009-0630/15/2/25
Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031, China
Funds: supported by ITER IO, the National Basic Research Program of China (973 Program, No. 2008CB717906) and the National Special Support for R&D on Science and Technology for ITER (No. 2008GB102000)
This paper presents the evolution of the design of cold mass support for the ITER magnet feeder system. The glass fibers in the cylinder and the flanges of the normal G10 support are discontinuous in the preliminary design. The heat load of this support from the analysis is only 4.86 W. However, the mechanical test of the prototype showed that it can only endure 9 kN lateral force, which is significantly less than the required 20 kN. So, the configuration of the glass fibers in the cylinders and flanges of this G10 support are modified by changing it to a continuous and knitted type to reinforce the support, and then a new improved prototype is manufactured and tested. It could endure 15 kN lateral forces this time, but still not meet the required 20 kN. Finally, the SS316LN material is chosen for the cold mass supports. The analysis results show that it is safe under 20 kN lateral forces with the heat load increased to 14.8 W. Considering the practical application, the requirements of strength is of primary importance. So, this SS316LN cold mass support is acceptable for the ITER magnet feeder system. On the other hand, the design idea of using continuous and knitted glass fibers to reinforce the strength of a G10 support is a good reference for the case with a lower heat load and not too high Lorentz force.
Li, S., Zeng, F., Zhang, Q. et al. Study on a compact pulse forming line-Marx type high voltage pulse generator. Review of Scientific Instruments, 2025, 96(1): 014707.
DOI:10.1063/5.0233985
2.
Luo, W., Ren, C., Huang, B. et al. Impact of overvoltage on the mode transition of the spark gap switch: from edge breakdown to stochastic breakdown. Plasma Sources Science and Technology, 2024, 33(11): 115003.
DOI:10.1088/1361-6595/ad8aeb
3.
Wang, Y., Li, J., Jiang, M. et al. The effects of pulse voltage rise time on the nanosecond pulsed breakdown of nitrogen spark switch at atmospheric pressure with 3D PIC-MCC model. Physics of Plasmas, 2023, 30(4): 043901.
DOI:10.1063/5.0138011
4.
Jia, Y., Xie, K., Ding, Y. et al. Special issue on selected papers from CEPC 2021. Plasma Science and Technology, 2022, 24(7): 070101.
DOI:10.1088/2058-6272/ac75c9
DownLoad: